OEM Gas Analyzer ANDROS 6552
Available with two gas channels, the Andros 6552 can be configured for specific types of refrigeration plants or as a general purpose device that can be applied to any type or combination of refrigeration systems that may employ Freons and Carbon Dioxide.
Key Features of Andros 6552 Gas Analyzer
OEM gas sensor detects Freon refrigerants and Carbon Dioxide for leak detection and other applications
- Measure up to 5 gases: 3 via NDIR and 2 via plug-in sensors
- RS232 or USB
- Most types of Freons
- Field upgradable to measure additional gases
Benefits of Andros 6552 Gas Analyzer
Highly Accurate Calibration
Every Andros 6552 system is individually calibrated for operation from 0°C to 50°C over the entire range of specified concentrations. The results of this intensive calibration process are stored within each system providing the most accurate analysis possible. This attention to detail provides a highly accurate factory calibration of the NDIR analyzer. Andros is so confident in our factory calibration that our customers need never calibrate the NDIR analyzer again.
The Andros 6552 is designed to meet or exceed EN 14624,“performance of mobile leak detectors and of room controllers of halogenated refrigerants”.
High Stability: Rapid Warm-Up
The enhanced optics and electronics of the 6552 have virtually eliminated zero drift after the initial warm up period. The temperature and pressure compensation eliminates the major causes of span drift in many NDIR instruments.
Unique Optical Architecture
The Andros 6550 Series offers greater design flexibility to OEMs due to its small overall size, our ability to customize subsystem designs to your specifications, and low power consumption. Our analyzer can be fitted into a wide variety of enclosures.
Comprehensive Software Architecture
The Andros Operating System (OS) software and communications protocol is designed to make system integration simple and fast.
|Response time||Response times are specified at a sample flow rate of 1 liter per minute through the 6552 sample cell.|
|Data refresh rate||1 second|
|Warm-up time||30 minutes fully stable, 3 minutes for reduced accuracy unless zeroed prior to taking measurement|
|Operating Temperature||0° - 70°C (32° - 158° F), accuracy not specified > 50°C|
|Operating humidity||To 95% RH (Non-condensing)|
|Operating altitude||-300 to 3,000m (-1,000 to 10,000 ft)|
|Host communication||USB or RS232C asynchronous serial; 19,200 bps or 9,600 bps (default is 19,200)|
|Size||19.18 cm L, 7.37 cm W, 5.03 cm H (7.55 x 2.90 x 1.98 in)|
|Weight||0.3 kg (0.8 lb)|
|Input power||+12 Volts DC nominal (+9 to +16)|
|Power consumption||1.8 Watts average at 12 VDC|
|Warranty||1 year parts and labor warranty|
|Compliance||Designed to meet or exceed EN 14624,“performance of mobile leak detectors and of room controllers of halogenated refrigerants”|
|Standard freons available: R22, R134A, R404A, R407C, R410A, R507, R422A, R422D|
|Measurement Method||Gas||Resolution||Messbereich||Accuracy||Precision||Response Time|
|NDIR (Non-Dispersive Infrared) on board||Most CFC, HFC and HCFC refrigerants||1 ppm||1 to 100 ppm||±4 ppm abs. or ±3% rel.||±4 ppm abs. or ±3% rel.||T90 & T10 <3 Seconds|
|101 to 1,000 ppm||±5% rel.|
|1,001 to 10,000 ppm||+/- 8% rel.||±3% rel.|
|CO2||0.01%||0.01% to 2.00%||±0.02% abs. or ±3% rel.||±0.02% abs. or ±3% rel.||T90 & T10 <3 Seconds|
|2.01% to 20.00%||±5% rel.|
|Electrochemical sensors via connector||O2||
Performance dependent upon electrochemical sensor model