Stationary, fully digital and fast compact 2-color pyrometer with analog output and RS232 or RS485 interface, available with laser pilot light or through lens sighting system or integrated video camera. For temperatures from 600 to 3000 °C.
- highest accuracy
- wide ranges
- laser-pilot-light or through lens sighting
- analog and digital output
- built-in maximum value storage
- bus control of all parameters
- also 1-channel temperature display
- integrated TV camera (optional)
The pyrometer ISQ 5 is a digital, compact and fast 2-color pyrometer for non-contact temperature measurement. The pyrometer measures in the 2-color method (ratio method) in which two adjacent wavelengths are used for the temperature determination.
This technique offers the following advantages compared to standard 1-color pyrometers:
a. The temperature measurement is independent of the object’s emissivity in wide ranges and is unaffected by dust and other contaminants in the field of view.
b. The measuring object can be smaller than the spot size, measurements through dirty viewing windows are possible up to a certain contamination.
c. Additionally the pyrometer can be switched to 1-color mode and used like a conventional pyrometer in a spectral range near 0.9 μm.
d. The response time of only 10 ms facilitates the measurement of fast heating processes.
The ISQ 5 is equipped with a built-in lens contamination control system. The most important parameters as emissivity slope, exposure time and analog output can be set directly in the instrument.
Additionally the pyrometer can be connected to a PC via serial interface, enabling adjustments of further parameters with the delivered software InfraWin. This can be used for temperature indication, data logging and further analyzing of complete temperature processes.
- cyrstal growing
- rolling mills
- rotary kilns
- induction heating
|Temperature range:||(MB 14) 600 to 1400°C
(MB 18) 700 to 1800°C
(MB 25) 800 to 2500°C
(MB 30) 1000 to 3000°C
|Sub range:||Any range adjustable within the temperature range, minimum span 51°C|
|Spectral Range:||channel 1: 0.9 μm; channel 2: 1.05 μm|
|Power Supply: :||24 V DC ± 25%, stabilized, ripple < 50 mV|
|Power Consumption:||≤ 3 W (incl. active laser targeting light)|
|Analog Output:||0 to 20 mA or 4 to 20 mA, switchable, linear in temperature, load independent DC|
|Interface:||Optional RS232 or RS485 (addressable), half duplex, baud rate 1.2 up to 38.4 kBd|
|Resolution:||0.1°C at the interface at the analog output < 0.1% of the adjusted temperature range but min. 0.1°C|
|Isolation:||Power supply and digital output and analog output are galvanically isolated against each other|
|Parameters||Adjustable on the converter’s rear side: emissivity slope, response time, analog output 0 to 20 mA or 4 to 20 mA, online / offline mode
Additionally via interface adjustable and readable: 2-color / 1-color temperature signal, according to this emissivity slope or emissivity, temperature sub range, settings for maximum value storage, address, baud rate, switch off limit, warning level lens contamination monitoring system.
Via interface readable only: measured value, internal temperature of the unit
|Maximum Value Storage||Single or double storage, clear modes: time (off; 0.01 s; 0.05 s; 0.25 s; 1 s; 5 s; 25 s),
external clear contact, via interface or automatic „hot object mode“, hold-function for freezing the
current temperature reading (not for ISQ 5-C)
|Emissivity slope K:||(ε1 /ε2): 0.800 ... 1.250|
|Emissivity ε (in 1-color mode):||0.05 ... 1.00|
|Response time t90:||< 10 ms, adjustable to 0.01s; 0.05s; 0.25s; 1s; 3s; 10s|
|Switch off limit:||Adjustable via interface: 2% to 50%|
|Contamination Warning:||Relay contact, max. continuous current 0.4 A, setting of the switch level: 0 (off) ... 99%|
(25°C, K=1, t90=1 s)
|< 1500°C: 0.5% of reading in °C + 2°C
> 1500°C: 1% of reading in °C
|Repeatability:||0.2% of reading in °C + 2°C|
|Noise equivalent temperature
(K=1, t90=10 ms, Tamb.=10...40°C)
MB 14: 1°C (at 610°C meas. temperature); 0.1°C (at 800°C meas. temperature)
MB 25: 0.4°C (at 810°C meas. temperature); 0.1°C (at 900°C meas. temperature)
MB 30: 0.2°C (at 1010°C meas. temperature); 0.1°C (at 1100°C meas. temperature)
|Temperature Dependence:||0.25°C per °C deviation of ambient temperature from 25°C|
|Sighting System:||Laser targeting light (max. power level < 1 mW, λ= 630-680 nm, CDRH class II) or thru-lens view finder or video module|
|Ambient Temperature:||0 to 70°C|
|Storage Temperature:||-20 to 70°C|
|Protection class:||IP65 (DIN 40050)|
|CE-label:||According to EU directives about electromagnetic immunity|
|Additional technical data for pyrometers with built-in video module:|
|Video signal:||CCIR norm approx. 1 Vpp at 75 W, 50 Hz (special option: EIA norm 60 Hz)|
|Array size:||CCIR norm: 628 x 583 pixels, black & white EIA norm: 510 x 492 pixels, black & white|
|Exposure:||automatic, additionally 3-levels controlled by the measuring temperature|
|Field of view:||approx. 10% x 14% of focused distance|
|Date/time:||real-time clock with at least 3 days spare run|
|Video output plug:||separate round plug at the pyrometer, not galvanically separated to the pyrometers power supply|
|Picture insertions:||target marking; unit number or user text (max. 12 characters), time and/or date; (individually switchable), measuring temperature, emissivity slope or emissivity|